I wanted to share my experience with waxing my bike chains.
I was resistant to waxing my chains because it seems that a lot of people felt it was “too much work”.
But having to constantly clean black shit off my chains after every ride, then spend time degreasing and re-lubing, I figured I’d try waxing when I got my gravel bike.
Now, thousands of KM later and having converted all three bikes to waxed, there’s no way I’d go back. The time saved could be measured in hours per month.
First, the biggest complaint is chain prep. Yeah, regardless if you’re waxing or not, you’ll need to prep a new chain by removing the factory grease. With waxed, you do this once, and no more worrying about degreasing ever again. Make like easy and get Silca’s chain stripper, and it’s a 10 minute, one-step process.
Ongoing chain maintenance couldn’t be easier. After every ride, give the chain a quick wipe (or not). My chain stays clean, even after a 200 km ride.
And if you ride in wet or dirty conditions? Guess what, you’re in for a LOT of work if you lube your chain. With waxed, keep a second (or third) chain ready to go, and you just swap it out (10 seconds of effort). Take the dirty chain, give it a wipe if it’s only been wet, or pour boiled water onto it if you want to “reset” the chain to bare metal. Then drop it into the waxing pot for a re-wax. You don’t have to stand at the pot, so there’s no real time commitment here. I’ve spent more time completely dirtying large microfiber cloths trying to get my chain “clean” when lubed (hint: it’s never clean if you use a wet lube, not without solvents and an ultrasonic cleaner).
For actual immersion wax, I do it every 1000 km (sooner than you need to), and use a drip wax every 200 - 250 km to keep things fresh.
Honestly, wax is easier, cleaner, and takes less time to maintain vs wet lube.
The only downsides? The initial cost to get started. But this is offset by not having to replace chains or other components prematurely. You actually save money in the long-term when using waxed chains.
Some might argue that “you can’t run waxed chains in muddy or constantly rainy conditions”. Well, at the same time, your wet lube isn’t really helping matters in those situations, either. Waxed is still better, and you can swap chains much faster than you can clean the grinding paste from a wet lubed chain.
Who would I not recommend waxed chains to? Someone who rarely uses their bike. Drip lube will be “good enough” in those cases. But anyone else would benefit from waxing their chain.
You know what’s even easier? Forgetting to lube your chain for a while. Then avoid lubing it out of shame to face your failure. Then measuring the chain wear after a year to discover no significant degradation.*
* Might require extra strong ebike-specific chains like KMC X11e EPT
Even easier is not caring or even knowing that you are supposed to do anything.
Ah, you must be one of those cyclists I can hear a mile away! SQUEAK, SQUEAK, SQUEAK!! 😂
Another surprising thing for me is that at no point did it start making shameful noises.
Plot twist: You’re actually using a carbon belt drive. 😆
7 years and counting. Have never had any maintenance on my belt. The Alfine 11 has had an oil change though.
Sounds like a dream! I’m sure at some point I’ll go with a belt drive. For now, I’m quite content with a low-maintenance chain drivetrain. Especially for their ubiquity, lower cost, and ease of repair while out in the middle of nowhere. LOL
It’s been very easy. Although I will say my use case is a 9km urban commute. Any issues I can jump on a train to the local bike shop.
Changing a rear tyre on a split frame in the middle of no where would be beyond me.
Or they are Dutch and have a fully-enclosed chain that never gets wet or dirty.
One thing I’ve done with my winter bike is added a front fender extender (DIY), which prevents any spray from hitting the front chainrings, chain, or down tube. Last year, it was a total game changer. The only thing I couldn’t really help with was spray from the rear fender, which drips downwards onto the chain and cassette.
I don’t even think a Dutch-style chain guard would help prevent contamination from the rear cassette getting drenched.
But the best “winter bike” is one with an internal gear hub, and a belt drive. And an aluminum frame. Unless you really abuse the hell out of it, there should be very little to worry about.
Haha, luckily I haven’t biked for quite a few years. My work is pretty away and I can play Ghost of Tsushima on the train.
Then measuring the chain wear after a year to discover no significant degradation.
How many miles/km?
Yes, good chains last longer. But good waxed chains can outlive the life of some bikes (20,000km on a waxed chain is not unheard of). And it preserves the components at the same time.
Not too many, perhaps 2000km. Spring/summer/fall, no water or dirt riding. The cassette is SLX, derailleur and shifter are XT. I don’t ride a huge amount at the highest gears which suffer from higher wear due to the fewer teeth count. I recently lubed it with Silca Synerg-e and it’s bit quieter but the shifting performance was excellent before and after that. With all that said, I have no doubt I’ve worn it more than if I had properly maintained it. Perhaps significantly more. Nevertheless I was flabbergasted at the state of the drivetrain after this much mismaintenance. 😂
Yeah, with 2000km, I wouldn’t expect much wear from a high-end chain like that. Before waxing, I was using Synergetic, which does help to preserve components. But it was still dirty, and I just got tired of always seeing black when I wiped the chain!
Now, I can literally put a dropped chain back on my chainring, and don’t even have to wipe my hands. It’s wild how clean a chain can be after 1000km of low effort maintenance!
So you’re saying I’m the perfect target audience for waxing? 🤔
Unless you don’t ride your bike, you are the perfect target audience for waxing! LOL
Counter-point: Here’s how I lube my chain.
Whenever the squeaking annoys me too much, I apply some lube.
Done.Same. When it rusts I replace it
When it’s time to replace it, I just buy another '90s MTB for 100€.
Be sure that you’re checking your chain for wear… and your cassette… and chainrings. That approach might work well for some, but squeaking is already a sign that wear has been occuring.
I don’t see why anyone would need to go thru all that when we’re talking about parts that will need to be replaced at some anyway point no matter how good care you take of them.
For me, my bike is to be used and abused. Yeah maybe my chain and cassette wears faster than with a proper maintenance but I also just keep riding way past that untill it effectively becomes unuseable. My chain is already stretched to the point I’m supposed to replace it and there’s several teeth missing on my rear cassette but I notice no difference in performance. The shifting is going to be more or less shit either way because a new derailleur stays straight on my use for about 3 days. I’ve already mastered the trail-side derailleur adjustment by grabbing it with bare hands and bending it straight(er)
I don’t see why anyone would need to go thru all that when we’re talking about parts that will need to be replaced at some anyway point no matter how good care you take of them.
Plenty of reasons, even when you acknowledge that parts will eventually need to be replaced:
- Convenience.
- Quieter ride.
- Cleaner.
- No solvents when you need to really clean the chain.
- Saves a LOT of money, especially when some newer cassettes are $300+, chains up to $100, etc. But even in my older bike, where the components are cheap, I’d rather not be spending money sooner and more often.
- As with the above point, components last significantly longer, and work better for longer (i.e. better shifting, no chain skipping, etc.).
- If you count watts, waxing will save them.
- Because you aren’t replacing components as often, this has environmental benefits, too.
I’m not a casual rider, so I want my bikes to run smoothly and with as little effort to maintain as possible. For me, waxing has been a blessing.
My chain checklist -
Have I put oil on the chain this decade? Y/N
Done!
You lost me at 10-second chain swaps and boiling water.
You lost me at 10-second chain swaps
Wipperman connex master links. No tools required. Can be reused “for the life of the chain”. Takes a second to remove and re-connect. 10 second chain swap!
and boiling water.
Unlike with traditional bike chain lube, which require some rather harsh solvents to remove. Wax can be boiled off the chain when needed. You can go back to bare metal on a waxed chain without any solvents.
Not sure if there is a lighter weight version, but I used to run wax on motorcyles, it came as a spray can and went on almost like a clear plastic coating. Game changer for chain maintenance
Key and Peele would be proud of your use on the chain wax
Wow! Thanks for putting up this super informative post and following through so many comments. I love using a waxed chain and I think it’s definitely hard for people to jump to when their bike maintenance is essentially zero. I run wet lube on one bike for wet weather riding (like >50% of the year) so I know both sides pretty well. The wax chain is so much easier to clean and maintain it’s crazy.
It’ll be hard to convert anyone that just lets their bike run into the ground before they start taking care of it, but they’re also probably on bikes that are sub $500 and aren’t looking for efficiencies or endurance performance.
It’ll be hard to convert anyone that just lets their bike run into the ground before they start taking care of it, but they’re also probably on bikes that are sub $500 and aren’t looking for efficiencies or endurance performance.
I think that’s probably pretty accurate. If I had a bike kicking around that I may or may not use, I don’t even think I’d be waxing that chain.
I also think that a good number of people are simply scared away by “all the work” that goes into waxing.
I’m almost looking forward to the winter, where I can really compare my experience between wax and wet lube.
I’m thinking this isn’t really for commuters?
Why not? I’d think it would be perfect for commuters.
Cleaner, less maintenance, and long-term cost savings. 😀
I admire your optimism! My drivetrain is due for replacement, but maybe I’ll be better off just trying to maintain an oil chain and graduate to wax if I can keep it up. I could see myself investing in wax but not following through due to entrenched bad maintenance habits.
Neat! I just blast that shit with some WD-40 which isn’t even lube and go on my merry way!
I don’t like maintaining my bike much and the waxing seems like it’s something for people that do.
Just using a little bit of oil holds fine for a pretty long time for me, if I don’t ride in the rain a lot. I also never degrease my chain, I’ll wipe it off with rug and that’s it. And I feel like the nasty black chain is mostly a thing if you used too much oil? I am happy with my chain wear and actually surprised for how long it stays fine.
I don’t like maintaining my bike much and the waxing seems like it’s something for people that do.
For me, it’s the opposite. Maintaining a lubed chain required far more time and patience than waxing. In that sense, I can focus more on riding my bike (or maintaining it in other ways, if I choose to).
And I feel like the nasty black chain is mostly a thing if you used too much oil?
That black is metal + dirt + oil. Basically, a grinding paste between the pins of your chain + all the crap that stuck to your chain.
I was using a single drop of wet lube, and my chain would be forever dirty after each ride. I could attempt to wipe it clean with 2 or 3 large microfiber rags, and still not get it “clean”. But wiping doesn’t actually clean the dirty parts where wear is occurring, so it was a never ending battle with degreasing, solvent baths, re-lubing, wiping.
I mean, sure, I could just wipe and re-lube and call it a day, but for the amount of riding I do, I’d either have to be replacing chains every month, or more expensive components a few times a year. That’s not in my budget! LOL
Yeah i guess i’m not all that picky, and granted those waxed chains look great. I read that you save hours per month in maintenance, but i don’t think i spend an hour a year fiddling with my chain, haha.
I prefer belt drive with a sealed internal geared hub. It’s not for everyone or every situation but it’s nice riding in the wet and just putting the bike away after without thinking about cleaning and lubrication
Yeah, if you can get a belt drive, go for it. I think if I ever got an ebike, it would need to have a belt drive. There’s something about working on a heavy bike that makes me want to work on it far, far less than something that’s lightweight.
Wow, this is super insightful! Thanks! Been wondering about waxing chains. We’re getting into our wet season so this is definitely piquing my curiosity once again.
I just waxed the chain on my gravel bike and it’s going great so far. Maybe time to consider the mountain bikes. I do spend a lot of time lubing chains.
We’re getting into our wet season so this is definitely piquing my curiosity once again.
Winter here gets slushy and salty, and I burned through a few chains two winters ago, then invested in “rustproof” chains last year, which worked well, but keeping on top of cleaning the inside of the chain and relubing was a PITA.
This year, I’ll be rotating waxed chains.
I even use waxed chain through salt and snow. Hosed off once I get to work then compressed air to get the water off. Home side I hose it off then detach it and swish it in a tub of isopropyl and the next chain in the rotation goes on.
This will be my first winter with waxed chains. My only real concern is the drip wax treatments between immersion wax. Since I don’t bring my bikes inside where it’s warm, I think it would be too cold to apply drip wax. I think we have many below zero days, I’ll probably just keep rotating immersion waxed chains until it warms up.
I don’t even drip wax. I could probably stand to refresh them more often, but when I do I just slosh it in 99% iso mooched from work, then hang it up and heat gun it to drip off any gunk stuck in the wax still on the chain, then throw it right in my dedicated noname slow cooker.
If it gets really bad I have the ultrasonic tub but usuallly I don’t
How do you melt the initial wax? Watching videos people use crockpots.
Doesn’t that ruin the pot? Do you have a dedicated pot for the wax?
Thrift stores are full of old crock pots. We used to get them for candle making.
If you use Silcas hot melt, then you can actually just boil the bag and put the chain in there. I haven’t used it like that, but instead just got an inexpensive slow cooker (most are <$25 or nearly free if second hand).
It doesn’t really “ruin” the pot, but I would dedicate it to wax only.
Interestingly enough, I’ve discovered wax melting pots designed specifically for melting waxes (i.e. for candle making), and while they might be a little more expensive than a slow cooker, they offer finer temperature control and may be slightly more convenient to use. With a cheap slow cooker, I’m quite happy!
Appreciate the advice!
I’ll check out some thrift stores / garage sales.
We also have a few candles that could stand to be remelted and reset, so perhaps their fly by the SO better if it’s for multiple uses :)
I use a small wax heater for removing body hair. 20$ and gets the job done. If you plan to do more than one chain at a time though, it’s too small. I’ll probably buy a used crock pot or instant pot at some time to wax more than one chain at a time.
I just use some cheapo liquid chain wax on my bike and I dont clean my chain very often, I just put some new wax on the chain when it gets just even slightly squeaky. I have noticed that almost no dirt stays on the drivetrain with wax, it just falls off after a few km. Everything stuck to the chain when using oil, so its an improvement and I dont spend nearly as much effort on it as you do.
Yup! Even drip wax will give better results vs. wet lube. The cleanliness blows me away every time!
I was at a group ride and showed some of the guys how clean the chain was… wiped it with my bare hands, and nothing. That was after like 60km of riding! LOL
The SILCA strip chip does a great job of eliminating the need for chain prep. Worth the extra cost, if you don’t want to mess around with harsh chemicals.
Waxed chains are the bees knees. I’ll never go back to using lube.
The SILCA strip chip does a great job of eliminating the need for chain prep. Worth the extra cost, if you don’t want to mess around with harsh chemicals.
I actually ordered some, realized that the slow cooker I was using couldn’t get to the right temperature for it, and sent it back.
It would have been easier, for sure. But the Chain Stripper is also really easy and can be reused. I’ll probably never run out, considering that I may only need to use it once every few years (per new chain). LOL
I used to thin paraffin wax with xylene just enough to make a solution that stays liquid and apply it to the chain from an old chain oil dripper bottle. If applied liberally it flushes out what little dirt has accumulated on the chain and after a quick wipe you’re done. The xylene evaporates leaving you with a waxed chain.
I used dry lubes for a while too but found the homemade wax liquid the most trouble-free option.
Sounds like you made a DIY version of a commercial drip wax. I use Silca’s drip wax, and I’m getting really good value out of it, so I’m not motivated enough to try something homemade. But I’m glad it works for you, and no doubt is better than most other lubes!
I really want to try waxing my chain but I commute on my bike and more than half the year it is wet and rainy so I had always read that it wouldn’t really be suitable due to the wetness. It is interesting to hear that this may not actually be as much of an issue as I was lead to believe by everything I had dead about it.
I generally keep on top of my maintainance and will wash the bike usually once a week including cleaning the filthy as fuck chain.
Think I may look into waxing again after reading this.
Unless your commutes are 150 km a day, wax will still be better than wet lube. Rotating among multiple chains would be the way to go.
The lower the speed count, the less expensive the chain, but you’ll save money in the long run, even with multiple 11 speed chains (which are way more expensive than something like a 7/8 speed chain).
I generally keep on top of my maintainance and will wash the bike usually once a week including cleaning the filthy as fuck chain.
I got tired of that. And realistically, you’ll never get a “clean” chain when using wet lube unless you use an ultrasonic cleaner + solvents (and run it through multiple cleaning cycles). You can clean the outside of the chain, but the wear happens around the pins, and you can’t wipe that clean.
Cheers for the info. I absolutely do not have the money to try this just yet but I will be keeping it in mind to do in the future as I’m sick of the black shit everywhere!
